The Metal Man at Kempton
-
- Posts: 857
- Joined: Tue May 27, 2008 2:19 pm
- Location: SURREY UK
The Metal Man at Kempton
Hi Chaps, especially those near enough to go to Kempton Jumble.
For the third time in succession the Metal Man wasn't there. Does anybody know if he is coming back ?
I don't wish to be insensitive if there is a health problem, but I really miss that wonderful selection of materials at reasonable prices. I don't know where else to go, particularly for the stainless. Just started on two little bikes, one metric and one imperial, intending to replace all the fasteners and studs with stainless.
Stan
For the third time in succession the Metal Man wasn't there. Does anybody know if he is coming back ?
I don't wish to be insensitive if there is a health problem, but I really miss that wonderful selection of materials at reasonable prices. I don't know where else to go, particularly for the stainless. Just started on two little bikes, one metric and one imperial, intending to replace all the fasteners and studs with stainless.
Stan
-
- Member
- Posts: 225
- Joined: Sat Jan 01, 2000 12:00 am
- Location: HAMPSHIRE UK
Re: The Metal Man at Kempton
He won't be coming back, prostrate troubles have forced him to give up.
-
- Member
- Posts: 64
- Joined: Mon Oct 17, 2011 9:34 pm
- Location: Bedfordshire UK
Re: The Metal Man at Kempton
There was a stand selling metal at Kempton yesterday it was right at the end near the overflow car park. Hopefully he will be there next time.
-
- Posts: 857
- Joined: Tue May 27, 2008 2:19 pm
- Location: SURREY UK
Re: The Metal Man at Kempton
Thanks for the replies Dodger and Beefheart.
Well at least I know and can stop fretting. The other chap at Kempton doesn't stock the same range but i'll Check next time if I haven't found a source. My local metal retailer in Crawley can get stainless but only in 15 foot lengths. That's a bit much even for the smaller sizes. I have got used to the metal man just being there for the 12 years I have been attending Kempton. Such a shame he has hit bad health.
Stan
Well at least I know and can stop fretting. The other chap at Kempton doesn't stock the same range but i'll Check next time if I haven't found a source. My local metal retailer in Crawley can get stainless but only in 15 foot lengths. That's a bit much even for the smaller sizes. I have got used to the metal man just being there for the 12 years I have been attending Kempton. Such a shame he has hit bad health.
Stan
-
- Member
- Posts: 452
- Joined: Tue May 27, 2003 1:00 am
- Location: SHROPSHIRE UK
Re: The Metal Man at Kempton
Try one of your local machining firms they usually have bar ends off cuts of various steel stock. Nothing ventured etc.
-
- Member
- Posts: 456
- Joined: Mon Jun 29, 2015 8:49 pm
- Location: East Yorkshire
Re: The Metal Man at Kempton
If you get stuck, there's a chap trades as blenco-metals, based in Doncaster, on ebay. He does get to the autojumbles at Newark and Rufforth (probably others too) and stocks Whitworth sizes in both stainless and brass hexagon and bar), If I need only small amounts and there's nothing else on the list, then I'd sooner pay postage than fuel and exhorbitant entrance costs to some of the jumbles. Rufforth has reduced its cost markedly over the last couple of years, but unless your interests lie in drug parafinalia and household cleaning products along with cheap chinese tools, there not a lot else there nowadays
Steve
Steve
- Peter Morris
- Member
- Posts: 733
- Joined: Wed Mar 05, 2014 4:21 pm
- Location: SURREY UK
Re: The Metal Man at Kempton
There was a stall selling metals on the right hand side near the entrance at Kempton yesterday, I bought 3 sizes of SS rod for making studs, 1 metre long..... 35 quid. I thought that was fair.
😠Just seen Beefheart's post.
😠Just seen Beefheart's post.
-
- Posts: 857
- Joined: Tue May 27, 2008 2:19 pm
- Location: SURREY UK
Re: The Metal Man at Kempton
Thanks chaps. Some good leads there.
Stan
Stan
-
- Member
- Posts: 1439
- Joined: Sat Oct 09, 2010 9:17 pm
- Location: ABERTAWE UK
Re: The Metal Man at Kempton
I buy my metal, ferrous and non-ferous from Noggin End Metals, Macc Models and Metals4u, but maybe none of these companies sell fasteners, Nooky's nuts supply all my fasteners.
https://www.nogginend.com/
https://www.metals4u.co.uk/?utm_source= ... 3E%3EExact
https://maccmodels.co.uk/
Colin
https://www.nogginend.com/
https://www.metals4u.co.uk/?utm_source= ... 3E%3EExact
https://maccmodels.co.uk/
Colin
only dead fish go with the flow