Hi
A friend of mine have recommended me to seal the valve guides (to the valve shafts).
Can I buy such seals or can I make some myself?
The bike is G12 1965
Regards Ib
(My friend has a Norton so it wont help to look at his)
Sealing the valve guide
-
- Member
- Posts: 330
- Joined: Thu Jan 01, 1998 12:00 am
- Location: FYN DENMARK
- Contact:
-
- Posts: 102
- Joined: Mon Oct 02, 2017 8:27 pm
- Location: Seattle area, WA USA
Re: Sealing the valve guide
Hello Ib, most people will buy them from a parts supplier. They are sold and packaged for specific engines, and are not a generic part. They come in a variety of sizes, materials, and designs. Common to all of them is the ability to allow a small amount of oil to pass thru the sealing materials.
Finding one to fit your valve guide, and still leave enough distance above the seal when the valve is fully open will be your challenge. Below is a link to an example.
https://images.app.goo.gl/KBMmNwd6JQyPimCM7
Ciao,
DC
Finding one to fit your valve guide, and still leave enough distance above the seal when the valve is fully open will be your challenge. Below is a link to an example.
https://images.app.goo.gl/KBMmNwd6JQyPimCM7
Ciao,
DC
Dick Casey
The RideNut
The RideNut
- Rob Harknett
- Member
- Posts: 11236
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Sealing the valve guide
The old bikes have run for years without sealers. Which have not had the years our old bikes have had, to prove themselves, they just keep on running. I would ask myself questions.
Are the sealers as equally robust? I am putting something else on the bike to fail and cause problems. Does the bike really need them.
Are the sealers as equally robust? I am putting something else on the bike to fail and cause problems. Does the bike really need them.
-
- Posts: 2886
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Sealing the valve guide
Hi
I'd be far more comfortable not fitting seals and knowing that if anything the valve stems are being over oiled rather than fitting seals which may lead to under oiling and seizure.
Regards Mick
I'd be far more comfortable not fitting seals and knowing that if anything the valve stems are being over oiled rather than fitting seals which may lead to under oiling and seizure.
Regards Mick
-
- Member
- Posts: 330
- Joined: Thu Jan 01, 1998 12:00 am
- Location: FYN DENMARK
- Contact:
Re: Sealing the valve guide
I think You got a point there.Mick D wrote:Hi
I'd be far more comfortable not fitting seals and knowing that if anything the valve stems are being over oiled rather than fitting seals which may lead to under oiling and seizure.
Regards Mick
It will bring me to my next question:
What will be the ideal play between the stem diameter and the guide diameter?
Regards Ib
-
- Member
- Posts: 328
- Joined: Mon Jan 01, 1990 12:00 am
- Location: DENMARK
Re: Sealing the valve guide
Hi Ib
My manual says Inlet min 0.05mm max 0.07mm, Exhaust min 0.07mm max 0.1mm
Poul
My manual says Inlet min 0.05mm max 0.07mm, Exhaust min 0.07mm max 0.1mm
Poul
-
- Posts: 592
- Joined: Thu May 06, 2004 1:00 am
- Location: KENT UK
Re: Sealing the valve guide
Only fit seals to the inlet valve stems. What they do is to stop oil being sucked into the cylinder on the inlet stroke. As said before if the valves and guides are not worn seals should not be needed on our elderly ladies.Ib-Denmark wrote:Hi
A friend of mine have recommended me to seal the valve guides (to the valve shafts).
Can I buy such seals or can I make some myself?
The bike is G12 1965
Regards Ib
(My friend has a Norton so it wont help to look at his)
- Taid
- Posts: 710
- Joined: Mon Oct 07, 2019 3:35 pm
- Location: Shropshire UK
Re: Sealing the valve guide
Gives me a name for mine .. "Mrs Tiverton"pkr87 wrote: ..... on our elderly ladies.
Thanks
___
Now sold ... 1956 AJS 16MS Bitsa .. HSU 414 .. rebuilt/re-registered 1987
Now sold ... 1956 AJS 16MS Bitsa .. HSU 414 .. rebuilt/re-registered 1987