Timing Gear Extractor
-
- Posts: 8
- Joined: Sat Dec 23, 2017 9:41 am
- Location: Hants, UK
Timing Gear Extractor
Help!! Does anyone in the Hants area have a Timing Gear Extractor I can borrow please??
Or know where I can Buy or hire?
Thanks Dan
Or know where I can Buy or hire?
Thanks Dan
- clive
- Member
- Posts: 5669
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Timing Gear Extractor
I think Dan is a recently joined club member but this is not showing and his posts are having to be authorised by a moderator. If I am correct on this Dan, please email Eamonn the webmaster to get your log in and membership linked (webmaster@jampot.com) with the details.
clive
if it ain't broke don't fix
if it ain't broke don't fix
-
- Posts: 8
- Joined: Sat Dec 23, 2017 9:41 am
- Location: Hants, UK
Re: Timing Gear Extractor
Have sent Eamonn an email. Thanks Clive
- ajscomboman
- Member
- Posts: 3958
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: Timing Gear Extractor
Well in that case being a member I have one you can borrow but not being able to drive due to a foot op you'll have to collect it from Southampton.
- clive
- Member
- Posts: 5669
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Timing Gear Extractor
clive wrote:I think Dan is a recently joined club member but this is not showing and his posts are having to be authorised by a moderator. If I am correct on this Dan, please email Eamonn the webmaster to get your log in and membership linked (webmaster@jampot.com) with the details.
Thought that might help the offers. I would be prepared to post one to borrow after Xmas as I am West London based.
clive
if it ain't broke don't fix
if it ain't broke don't fix
-
- Posts: 8
- Joined: Sat Dec 23, 2017 9:41 am
- Location: Hants, UK
Re: Timing Gear Extractor
Clive, tried signing in as Eamonn suggested but it would not accept it, cannot re register as username/email already used.
ajscomboman, thanks for the offer... very grateful. We can come down to get it.... if fact its 90% stripped so could put it in car and do the job in boot..... what day/time would suit....would Wednesday morning be ok?
ajscomboman, thanks for the offer... very grateful. We can come down to get it.... if fact its 90% stripped so could put it in car and do the job in boot..... what day/time would suit....would Wednesday morning be ok?
-
- Posts: 8
- Joined: Sat Dec 23, 2017 9:41 am
- Location: Hants, UK
Re: Timing Gear Extractor
Clive Eamonn has fixed it!!
- ajscomboman
- Member
- Posts: 3958
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: Timing Gear Extractor
Yep that'd be fine, should only be a couple of minutes to pull the gear off.DanSmith wrote:Clive, tried signing in as Eamonn suggested but it would not accept it, cannot re register as username/email already used.
ajscomboman, thanks for the offer... very grateful. We can come down to get it.... if fact its 90% stripped so could put it in car and do the job in boot..... what day/time would suit....would Wednesday morning be ok?
I'll send address details via PM.
-
- Member
- Posts: 3533
- Joined: Sun Jan 01, 1995 12:00 am
- Location: ESSEX UK
Re: Timing Gear Extractor
Yep that'd be fine, should only be a couple of minutes to pull the gear off.
I'll send address details via PM.[/quote]
How did it all go just a quick tug and it was off i bet he was pleased.
I'll send address details via PM.[/quote]
How did it all go just a quick tug and it was off i bet he was pleased.
Roy
- ajscomboman
- Member
- Posts: 3958
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: Timing Gear Extractor
How did it all go just a quick tug and it was off i bet he was pleased.[/quote]G15 Roy wrote:Yep that'd be fine, should only be a couple of minutes to pull the gear off.
I'll send address details via PM.
You know full well how it didn't go!!!!! I've used the puller on several gears but this bugger is really on there! So bloody tight it pulled the tang of the puller like a ring pull on a drinks can. Heated the gear up and still bugger all happened. I'll get the puller welded and may have a look at getting some pullers made as they're not available anywhere.