Head Gasket
-
- Member
- Posts: 1102
- Joined: Tue Jan 15, 2008 4:18 pm
- Location: SOMERSET UK
Head Gasket
A head gasket as suggested by the spares manual ( the copper gasket) won't fit my 1963 G80 500cc
Should it be 028100
Should it be 028100
You do not have the required permissions to view the files attached to this post.
Last edited by mikeydpippin on Sun Jan 28, 2018 9:59 pm, edited 3 times in total.
Mike
-
- Posts: 663
- Joined: Thu Feb 27, 2014 9:27 am
- Location: Kent, England
Re: Head Gasket
Hi Mike
Looks to me like you are trying to fit a head gasket to the cylinder base gasket position. This gasket should be a thin paper one.
The mating surfaces of the crankcase halves do not look right either - looks like they may be from different engines.
Jim
Looks to me like you are trying to fit a head gasket to the cylinder base gasket position. This gasket should be a thin paper one.
The mating surfaces of the crankcase halves do not look right either - looks like they may be from different engines.
Jim
Too old to Rock and Roll but too young to die.
1952 G80 rigid, 1960 G12 DL / Watsonian Monza, 1954 G80S.
1952 G80 rigid, 1960 G12 DL / Watsonian Monza, 1954 G80S.
-
- Member
- Posts: 1102
- Joined: Tue Jan 15, 2008 4:18 pm
- Location: SOMERSET UK
Re: Head Gasket
Thanks Jim put gasket on wrong place guess I have right gasket wrong location, been in shed too long I reckon. edited post Thanks.
Your right the crankcases do look like there from different bikes, turning into a bodge this bike considering one owner from new, engine number removed, and over tightened and cracked alloy on oil inlet pipe.
What next, hopefully the crankcases will be ok..
Your right the crankcases do look like there from different bikes, turning into a bodge this bike considering one owner from new, engine number removed, and over tightened and cracked alloy on oil inlet pipe.
What next, hopefully the crankcases will be ok..
Mike
-
- Member
- Posts: 8559
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Head Gasket
Mike, I hate to say this and I know the close-up photo exaggerates the mismatch of the c/case halves but if you go ahead with that you can probably expect to have an oil leak from the cylinder base. It's only a very thin paper cylinder base gasket.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
-
- Member
- Posts: 1102
- Joined: Tue Jan 15, 2008 4:18 pm
- Location: SOMERSET UK
Re: Head Gasket
Oh dear, probably explains why the engine number was removed, probably not a G80 half on the left side ( looking at photo)
Mike
-
- Member
- Posts: 1176
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: KENT UK
Re: Head Gasket
Were the crankcases an ebay bargain?
-
- Member
- Posts: 8559
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Head Gasket
Does the bike have a V5? Is the frame number still there and unmolested?mikeydpippin wrote:...........one owner from new, engine number removed, and over tightened and cracked alloy on oil inlet pipe.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
-
- Member
- Posts: 1102
- Joined: Tue Jan 15, 2008 4:18 pm
- Location: SOMERSET UK
Re: Head Gasket
No Nev,
Bought over the phone from scouser, told one owner from new, and it had been driven into shed in good working order but been off rd for 30yrs, since delivery have found engine numbers has been removed casting around oil return pipe cracked and broken (had that repaired) fork leg bolt hole casting broken (being filled in today and I will redrill and helicoil).
Original fuel tank rotted underneath (but I have a tank that will fit, but not the knee knocker tank).and now realise the crankcases are different, just hope the flywheels been balanced.
No V5 so will have to get age related, and apply for dating cert with frame number. (frame number readable and on frame)
Tinware all good though, and most bits there, and a bit of side to side play on connecting rod, but no up and down play.
Spoke to Steve, no chance of getting a G80 crankcase with engine numbers on, Steve suggested building as it is and sorting out any probs as and when they arise. May be able to get engine numbers stamped on it, but main concern is what to do with these crankcase halves,
Lesson learnt, Go see bike before buying it.. thought £700 was a steal.
Bought over the phone from scouser, told one owner from new, and it had been driven into shed in good working order but been off rd for 30yrs, since delivery have found engine numbers has been removed casting around oil return pipe cracked and broken (had that repaired) fork leg bolt hole casting broken (being filled in today and I will redrill and helicoil).
Original fuel tank rotted underneath (but I have a tank that will fit, but not the knee knocker tank).and now realise the crankcases are different, just hope the flywheels been balanced.
No V5 so will have to get age related, and apply for dating cert with frame number. (frame number readable and on frame)
Tinware all good though, and most bits there, and a bit of side to side play on connecting rod, but no up and down play.
Spoke to Steve, no chance of getting a G80 crankcase with engine numbers on, Steve suggested building as it is and sorting out any probs as and when they arise. May be able to get engine numbers stamped on it, but main concern is what to do with these crankcase halves,
Lesson learnt, Go see bike before buying it.. thought £700 was a steal.
Last edited by mikeydpippin on Mon Jan 29, 2018 2:51 pm, edited 2 times in total.
Mike
-
- Member
- Posts: 289
- Joined: Sat Jan 01, 2000 12:00 am
- Location: S YORKS UK
Re: Head Gasket
I would be checking the main bearing alignment .
Guessing that originally the crankcases were machined as a matched pair , and they obviously aren't
Guessing that originally the crankcases were machined as a matched pair , and they obviously aren't
-
- Member
- Posts: 1902
- Joined: Wed Jan 01, 1992 12:00 am
- Location: SURREY UK
Re: Head Gasket
You could use a pair of G3, Model 16 or 18 if there are any available. My Twingle has G3 stamped cases even though it's a 500!