Exhaust valve seat again G11CS
-
- Member
- Posts: 601
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: FRANCE
Re: Exhaust valve seat again G11CS
Hi Clive,
I can recommend T & L Engineering, in Elstow (Bedford). They are helpfull, and their prices are friendly. I have dealed with Derrick. They advertise in Jampot Magazine.
I can recommend T & L Engineering, in Elstow (Bedford). They are helpfull, and their prices are friendly. I have dealed with Derrick. They advertise in Jampot Magazine.
- clive
- Member
- Posts: 5669
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Exhaust valve seat again G11CS
Thanks for all the advice guys, our local section engineering genius has rotated the valve seat, under heat, and then pinned it through with a 4 BA screw. This is the fix he did on the other head. So for the time being this will be it. Unfortunately 5 days after my off road incident I decided to get my leg x-rayed, and 5 and a half hours in the local A and E and I am leaving with my leg in plaster due to a broken fibula. That's no driving and as the garage is 1.5 miles away I think the rebuild is going to have to go on hold for a while. ![Crying or Very Sad :cry:](./images/smilies/icon_cry.gif)
![Crying or Very Sad :cry:](./images/smilies/icon_cry.gif)
clive
if it ain't broke don't fix
if it ain't broke don't fix
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Exhaust valve seat again G11CS
Hope the break soon heals without further problems Clive. I seem to recall you once turning up at a Jampot rally years ago, with a whole leg in plaster. Now just you take care.
- clive
- Member
- Posts: 5669
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Exhaust valve seat again G11CS
Well the leg is mended and so I thought was the engine, but I had only gone about a mile and the gasket blew in that gap between the two barrels. Hey ho that means redoing the whole reassembly. It was a single gasket I had which I thought was ok but obviously not, or I didn't crank the head down properly. Good job I am retired.
clive
if it ain't broke don't fix
if it ain't broke don't fix
- ajscomboman
- Member
- Posts: 3958
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: Exhaust valve seat again G11CS
Got so fed up blowing gaskets on the CSR that I changed to solid copper with O rings around the oil-ways, touch wood all ok so far.
-
- Member
- Posts: 3533
- Joined: Sun Jan 01, 1995 12:00 am
- Location: ESSEX UK
Re: Exhaust valve seat again G11CS
But you must check them every 100 miles.ajscomboman wrote:Got so fed up blowing gaskets on the CSR that I changed to solid copper with O rings around the oil-ways, touch wood all ok so far.
Roy
- ajscomboman
- Member
- Posts: 3958
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: Exhaust valve seat again G11CS
Don't exaggerate, every 101 miles. ![Razz :P](./images/smilies/icon_razz.gif)
![Razz :P](./images/smilies/icon_razz.gif)
- clive
- Member
- Posts: 5669
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Exhaust valve seat again G11CS
Well that's the gasket replaced and cranked down as per instructions from Mr President. I imagine I will be making a warranty claim against him if the gasket goes again. ![Wink ;)](./images/smilies/icon_e_wink.gif)
![Wink ;)](./images/smilies/icon_e_wink.gif)
clive
if it ain't broke don't fix
if it ain't broke don't fix
- robcurrie
- Member
- Posts: 956
- Joined: Fri Dec 09, 2011 5:33 pm
- Location: Limpopo SOUTH AFRICA
- Contact:
Re: Exhaust valve seat again G11CS
No warranty, the only cover he offers is a layer of iron oxide and that doesn't apply to copper
Rob C
![Very Happy :rofl:](./images/smilies/rofl.gif)
Rob C
- clive
- Member
- Posts: 5669
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Exhaust valve seat again G11CS
So no warranty claim about 750 miles covered and no gasket problems. Drivers of undertaking cars that spill you down the road however have no such guarantee of no legal action, especially when you have a witness. 👽
clive
if it ain't broke don't fix
if it ain't broke don't fix