Starting problems when warm
-
- Member
- Posts: 7
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: SWEDEN
Starting problems when warm
Hi all.I am new on this forum.I have a AJS 30 CS from -58.He start quite easy when cold,but I kick my knee out of funktion when he is hot or warm.I have tested the magneto in my own test,it gives sparks 6 mm long when cold.I have seen somewhere.that it is more difficult to get a spark under compression.What is the problem?
- dave16mct
- Member
- Posts: 3264
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LANCASHIRE UK
Re: Starting problems when warm
The most likely cause is the condensor in the magneto has broken down. You can fit a Brightspark 'Easycap' condensor on the points plate but the old one needs to be disconnected and its buried in the end of the armature. Google Brightspark Magnetos to see the details.
Dave.
Dave.
- Ralph
- Member
- Posts: 88
- Joined: Tue Jan 07, 2020 7:00 pm
- Location: UK
Re: Starting problems when warm
Have you tried the spark when it's hot?
when electrics start to fail they very often
fail when hot but will work once cooled
down, I would suspect the condenser.
when electrics start to fail they very often
fail when hot but will work once cooled
down, I would suspect the condenser.
-
- Member
- Posts: 452
- Joined: Tue May 27, 2003 1:00 am
- Location: SHROPSHIRE UK
Re: Starting problems when warm
Magneto first to check, quite common fault with age.
- Duncan
- Member
- Posts: 2145
- Joined: Thu Jul 10, 2003 1:00 am
- Location: HAMPSHIRE UK
Re: Starting problems when warm
Sounds like a magneto/condenser issue but check some other simple things first like:
Do you have an insulating spacer between the carburettor and inlet manifold?
Is the engine running lean/is there an air leak on the manifold?
Are you valves/tappets correctly adjusted?
Are the HT leads in good condition and the spark plugs and plug cap?
Have you owned the bike for long, has it always been like this?
Do you have an insulating spacer between the carburettor and inlet manifold?
Is the engine running lean/is there an air leak on the manifold?
Are you valves/tappets correctly adjusted?
Are the HT leads in good condition and the spark plugs and plug cap?
Have you owned the bike for long, has it always been like this?
-
- Member
- Posts: 629
- Joined: Tue Oct 24, 2017 12:05 pm
- Location: DEVON UK
Re: Starting problems when warm
My G12 has had a full magneto rebuild but is still harder to start when hot. But genuine Champion spark plugs, and giving it a swift kick withOUT retarding the ignition have helped a lot.
Malc
Malc
- clive
- Member
- Posts: 5689
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Starting problems when warm
I agree with this, had to do it on a rebuilt mag after about 6 months of use which came with my 1958 G11CS. I was lucky and the "condensectomy" as described on the website was easy to do. I bought two Bright Spark units keeping one as a spare taped in the headlight in case the first gave up the ghost. Never got it out in the last 5 years except to show people what the Bright spark unit was like!dave16mct wrote:The most likely cause is the condensor in the magneto has broken down. You can fit a Brightspark 'Easycap' condensor on the points plate but the old one needs to be disconnected and its buried in the end of the armature. Google Brightspark Magnetos to see the details.
Dave.
clive
if it ain't broke don't fix
if it ain't broke don't fix
-
- Member
- Posts: 7
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: SWEDEN
Re: Starting problems when warm
Thankyou for all advise.I have now put in the Spark Bright things and now it will start even warm.
-
- Member
- Posts: 3542
- Joined: Sun Jan 01, 1995 12:00 am
- Location: ESSEX UK
Re: Starting problems when warm
Now where did I put it.clive wrote:I agree with this, had to do it on a rebuilt mag after about 6 months of use which came with my 1958 G11CS. I was lucky and the "condensectomy" as described on the website was easy to do. I bought two Bright Spark units keeping one as a spare taped in the headlight in case the first gave up the ghost. Never got it out in the last 5 years except to show people what the Bright spark unit was like!dave16mct wrote:The most likely cause is the condensor in the magneto has broken down. You can fit a Brightspark 'Easycap' condensor on the points plate but the old one needs to be disconnected and its buried in the end of the armature. Google Brightspark Magnetos to see the details.
Dave.
Roy
- clive
- Member
- Posts: 5689
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Starting problems when warm
Thats good news Lars. How about a photo?lasse wrote:Thankyou for all advise.I have now put in the Spark Bright things and now it will start even warm.
clive
if it ain't broke don't fix
if it ain't broke don't fix