woe woe G2 woe
-
- Posts: 98
- Joined: Fri Jan 16, 2004 12:00 am
- Location: KENT UK
woe woe G2 woe
Right
Spriddler is answering the piston question I think.
But the pictures are of an early tube breather, there is only one hole in the ring, so it has to be the long tube bolt.
The newer ring has two holes one for the fixing bolt (threaded) and one to let the pressure out.
Am I correct???
Spriddler is answering the piston question I think.
But the pictures are of an early tube breather, there is only one hole in the ring, so it has to be the long tube bolt.
The newer ring has two holes one for the fixing bolt (threaded) and one to let the pressure out.
Am I correct???
- chris kelly
- Posts: 288
- Joined: Mon Jan 01, 1996 12:00 am
- Location: OSTERGOTLAND SWEDEN
woe woe G2 woe
Hi Ken, Probably stating obvious, but "Technical Tips" on our home page mentions the breather several times..and a drawing. Article by John Allen. Lightweight engines.
Chris.
'My cat can beat up your cat!'
- Biscuit
- Deceased
- Posts: 3924
- Joined: Thu Jan 01, 1998 12:00 am
- Location: KENT UK
woe woe G2 woe
How can it be the long tube bolt type when there is no thread in the crankcase? This can only be some kind of interim model.
-
- Posts: 98
- Joined: Fri Jan 16, 2004 12:00 am
- Location: KENT UK
woe woe G2 woe
Alan
Some butcher has drilled the thread out and put the thread in the ring for what reason I no not. but it only has the one hole.
Some butcher has drilled the thread out and put the thread in the ring for what reason I no not. but it only has the one hole.
-
- Member
- Posts: 77
- Joined: Fri Aug 20, 2004 1:00 am
- Location: CHESHIRE UK
woe woe G2 woe
hi,
not been on here for a while having sold the g2 and bought a burgman.
i will try and give some details of the breather setup.
it is a three part system, "rotor" which is fitted to the crankshaft via a woodruff key.
"stator" that the rotor runs around inside.
and the "tube" that holds the stator in place, and allows the engine to breath out towards the rear sprocket.
on the early g2 the "tube was not threaded into the stator" but threaded at the top end to screw into the crankase and push fit into the stator.
a modification was made later on, because where the tube pushed into the rotor, sloppiness would occur, so the stator was threaded and so was the bottom of the tube, so they screwed together.
the thread at the top of the tube is not now needed as the two parts are now tight.
not very clear to read i know, but it is the best way i can explain it.
regards, alan.
not been on here for a while having sold the g2 and bought a burgman.
i will try and give some details of the breather setup.
it is a three part system, "rotor" which is fitted to the crankshaft via a woodruff key.
"stator" that the rotor runs around inside.
and the "tube" that holds the stator in place, and allows the engine to breath out towards the rear sprocket.
on the early g2 the "tube was not threaded into the stator" but threaded at the top end to screw into the crankase and push fit into the stator.
a modification was made later on, because where the tube pushed into the rotor, sloppiness would occur, so the stator was threaded and so was the bottom of the tube, so they screwed together.
the thread at the top of the tube is not now needed as the two parts are now tight.
not very clear to read i know, but it is the best way i can explain it.
regards, alan.
-
- Deceased
- Posts: 407
- Joined: Sat Nov 12, 2005 5:02 pm
- Location: SURREY UK
woe woe G2 woe
Would that all explanations are as clear - I don't have such a beast, but it is very clear to me!
-
- Posts: 98
- Joined: Fri Jan 16, 2004 12:00 am
- Location: KENT UK
woe woe G2 woe
Do you understand Itma cos I cant follow this now, I still think it was a butcher that got there first.
- Biscuit
- Deceased
- Posts: 3924
- Joined: Thu Jan 01, 1998 12:00 am
- Location: KENT UK
woe woe G2 woe
Eminently understandable. However, the final mod., that of no tube, two holes in the stator and a short bolt holding the stator is not mentioned.
As I suggested the setup Itma has must be an interim mod. All he needs to do is to fit a decent bolt with a hole through it.
As I suggested the setup Itma has must be an interim mod. All he needs to do is to fit a decent bolt with a hole through it.
-
- Posts: 7721
- Joined: Tue Nov 22, 2005 6:01 pm
- Location: UK
woe woe G2 woe
Exactly.
I shall make up a bolt, suitably holed; anyone give me an idea how big the original bore of this miscreant object was, or won`t it matter?
All my very long drills are 1/4" so that will probably settle it
I shall make up a bolt, suitably holed; anyone give me an idea how big the original bore of this miscreant object was, or won`t it matter?
All my very long drills are 1/4" so that will probably settle it
- Biscuit
- Deceased
- Posts: 3924
- Joined: Thu Jan 01, 1998 12:00 am
- Location: KENT UK
woe woe G2 woe
The hole in the hollow tuby thingy was less than a 1/4", so I think that would suffice.