Thanks G3 Bitsa, point taken I dont have to be that acurate.
Ken , like the idea of moving the advance unit not the backplate, I shell have to look in to this, Thanks
And Chris thanks I shall look at your idea as well.
Thanks all for you help DaveEdited by - davehutch on 02 Jan 2009 10:15:56 PM
Contact breaker back plate
- davehutch
- Posts: 192
- Joined: Sat Jul 19, 2008 4:05 pm
- Location: LEICESTERSHIRE UK
Contact breaker back plate
----Only a biker knows why a dog sticks his head out of a car window.
- Tolly
- Member
- Posts: 648
- Joined: Mon Jan 01, 2001 12:00 am
- Location: KENT UK
Contact breaker back plate
I know what you mean Dave, I had the same problem with my G5, you only have to move the screws and the plate tilts a minute amount but alters the point gap by quite a bit. I found the answer trial and error, this I mean by checking the timing and if it's out identify which way to turn the base plate, then turn it a guessed amount, tighten and check the timing again. It might take a few attempts to get it right. I must admit I got fed up with this and fitted electronic ignition and haven't looked back, best thing I could have done and in the long run you get your money back as I found the CB points didn't last long and they are quite pricey.
When I mention this to some purist they make comments on originality, but I reply saying that you cannot see the change unless the cover is removed and anyway if electronic ignition was about when these bikes were new I'm sure they would have fitted them at the factory.
When I mention this to some purist they make comments on originality, but I reply saying that you cannot see the change unless the cover is removed and anyway if electronic ignition was about when these bikes were new I'm sure they would have fitted them at the factory.
_______________________________________________________
Experience is something you don't get until just after you need it.
Experience is something you don't get until just after you need it.
- davehutch
- Posts: 192
- Joined: Sat Jul 19, 2008 4:05 pm
- Location: LEICESTERSHIRE UK
Contact breaker back plate
quote:
I know what you mean Dave, I had the same problem with my G5, you only have to move the screws and the plate tilts a minute amount but alters the point gap by quite a bit. I found the answer trial and error, this I mean by checking the timing and if it's out identify which way to turn the base plate, then turn it a guessed amount, tighten and check the timing again. It might take a few attempts to get it right. I must admit I got fed up with this and fitted and haven't looked back, best thing I could have done and in the long run you get your money back as I found the CB points didn't last long and they are quite pricey.
When I mention this to some purist they make comments on originality, but I reply saying that you cannot see the change unless the cover is removed and anyway if electronic ignition was about when these bikes were new I'm sure they would have fitted them at the factory.
Thanks Tolly, can you point me in the right direction where to get electronic ignition from. It's nice to know someone understands where i am comming from
Cheers Dave
I know what you mean Dave, I had the same problem with my G5, you only have to move the screws and the plate tilts a minute amount but alters the point gap by quite a bit. I found the answer trial and error, this I mean by checking the timing and if it's out identify which way to turn the base plate, then turn it a guessed amount, tighten and check the timing again. It might take a few attempts to get it right. I must admit I got fed up with this and fitted and haven't looked back, best thing I could have done and in the long run you get your money back as I found the CB points didn't last long and they are quite pricey.
When I mention this to some purist they make comments on originality, but I reply saying that you cannot see the change unless the cover is removed and anyway if electronic ignition was about when these bikes were new I'm sure they would have fitted them at the factory.
Thanks Tolly, can you point me in the right direction where to get electronic ignition from. It's nice to know someone understands where i am comming from
Cheers Dave
----Only a biker knows why a dog sticks his head out of a car window.
- Tolly
- Member
- Posts: 648
- Joined: Mon Jan 01, 2001 12:00 am
- Location: KENT UK
Contact breaker back plate
Hi Dave, I got mine from a local m/c garage that deals with old British bikes, Road Star they are from Dover, I'm also lucky in having the firm that makes them just 30 miles up the road. I bought a Boyer Bransden kit, here is there web address, if you look under dealers there may be one in your area.
http://www.boyerbransden.com/
Regards, Tolly
http://www.boyerbransden.com/
Regards, Tolly
_______________________________________________________
Experience is something you don't get until just after you need it.
Experience is something you don't get until just after you need it.
- davehutch
- Posts: 192
- Joined: Sat Jul 19, 2008 4:05 pm
- Location: LEICESTERSHIRE UK
Contact breaker back plate
Cheers Mate !!
----Only a biker knows why a dog sticks his head out of a car window.