on the scrounge again, but with the imminent arrival of all my engine cases, head etc back from the aqua blasters, can anybody point me in the direction of a decent engine rebuild article please? i really shouldn't need it, but it's 36 years since i rebuilt my last one and i've lost some grey matter since then. many thanks.
cheers, bb.
engine rebuild - 250
- borrowashboy
- Posts: 93
- Joined: Wed Jan 31, 2007 3:21 pm
- Location: DERBYSHIRE UK
- dave16mct
- Member
- Posts: 3246
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LANCASHIRE UK
engine rebuild - 250
Go to Christians archives and look for workshop manuals. The 57-64 is the one you want.
- borrowashboy
- Posts: 93
- Joined: Wed Jan 31, 2007 3:21 pm
- Location: DERBYSHIRE UK
engine rebuild - 250
hi dave, i've got that mate. will have to sit there with a box of cigars and a flask of tea one night and REALLY read it properly.
cheers, bb.
p.s. i really need one with big pictures. why on earth didn't haynes do a manual for the lightweight?Edited by - borrowashboy on 09 Dec 2011 8:30:31 PM
cheers, bb.
p.s. i really need one with big pictures. why on earth didn't haynes do a manual for the lightweight?Edited by - borrowashboy on 09 Dec 2011 8:30:31 PM
-
- Posts: 7721
- Joined: Tue Nov 22, 2005 6:01 pm
- Location: UK
engine rebuild - 250
just make sure you get all the blasting element out of every nook and cranny
quote:
why on earth didn't haynes do a manual for the lightweight?
Because by the time Haynes started printing manuals lightweight AMC bikes were down to about 5 quid each........, on a good day.
quote:
why on earth didn't haynes do a manual for the lightweight?
Because by the time Haynes started printing manuals lightweight AMC bikes were down to about 5 quid each........, on a good day.
- borrowashboy
- Posts: 93
- Joined: Wed Jan 31, 2007 3:21 pm
- Location: DERBYSHIRE UK
engine rebuild - 250
everything as clean as a new pin mate. all oilways etc clear. one good thing about water blasting. i must have been robbed in 75 then, because my model 14 csr cost me £60
cheers, bb.
ps, after digesting a bit more on the engine rebuild, off out to the shed to open the wellseal. unfortunately at the aqua blasters the locating pin for the big timing side bush went walkies, so spent half the morning finding one. luckily i've got one.
cheers, bb.
ps, after digesting a bit more on the engine rebuild, off out to the shed to open the wellseal. unfortunately at the aqua blasters the locating pin for the big timing side bush went walkies, so spent half the morning finding one. luckily i've got one.
- Duncan
- Member
- Posts: 2141
- Joined: Thu Jul 10, 2003 1:00 am
- Location: HAMPSHIRE UK
engine rebuild - 250
Ade
As Ken notes aqua blasting still uses an abrasive media, if the cases were mine I would still wash them thoroughly before use.
As Ken notes aqua blasting still uses an abrasive media, if the cases were mine I would still wash them thoroughly before use.
- borrowashboy
- Posts: 93
- Joined: Wed Jan 31, 2007 3:21 pm
- Location: DERBYSHIRE UK
engine rebuild - 250
done it mate, every hole, every inch is clean as a nun's mind
cheers, bb.
- borrowashboy
- Posts: 93
- Joined: Wed Jan 31, 2007 3:21 pm
- Location: DERBYSHIRE UK
engine rebuild - 250
p.s. photo of head/rockerbox on new photo's page.
cheers, bb.
cheers, bb.