AJS model 31 clutch
- greasemonkey62
- Posts: 562
- Joined: Wed Jun 16, 2010 12:37 pm
- Location: SOUTH YORKSHIRE UK
AJS model 31 clutch
Thanks very interesting, but the spring studs look similar to the standard amc studs why didnt you use the usual amc parts assuming I have this right?
- GOLDSTAR
- Member
- Posts: 2521
- Joined: Thu Sep 11, 2003 1:00 am
- Location: KENT UK
AJS model 31 clutch
did you braze those inserts in the chainwheel slots? nicely done, kind regards
- paul knapp
- Posts: 1645
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: SOUTH AUSTRALIA AUSTRALIA
AJS model 31 clutch
G'day Ray, that is a Norton clutch on my stock? '51 EASY2 Norton. I simply altered what I had ( being a tight arse, I don't buy what I can make) and knocked up a few other bits to make a crappy clutch into a more manageable one. I am not familiar with later AMC clutches, never seen one! If they are anything like this Norton one was, I hope I never see one!
Right on GOLDSTAR, i posted a series of photographs several months ago re the same basket drive slot repair and friction disc modification. I tacked them onto a posting started by a full member. Can't remember which one!
Right on GOLDSTAR, i posted a series of photographs several months ago re the same basket drive slot repair and friction disc modification. I tacked them onto a posting started by a full member. Can't remember which one!
___“As a hobby for the technically minded, motorcycling provides great scope.”
J.B.Nicholson
Don't worry about the world coming to an end today. It's already tomorrow in Australia!
_____________________________________________
J.B.Nicholson
Don't worry about the world coming to an end today. It's already tomorrow in Australia!
_____________________________________________
- paul knapp
- Posts: 1645
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: SOUTH AUSTRALIA AUSTRALIA
AJS model 31 clutch
....Just had a search GOLDSTAR, and the post was instigated by you on 25 th. February.
___“As a hobby for the technically minded, motorcycling provides great scope.”
J.B.Nicholson
Don't worry about the world coming to an end today. It's already tomorrow in Australia!
_____________________________________________
J.B.Nicholson
Don't worry about the world coming to an end today. It's already tomorrow in Australia!
_____________________________________________
- GOLDSTAR
- Member
- Posts: 2521
- Joined: Thu Sep 11, 2003 1:00 am
- Location: KENT UK
AJS model 31 clutch
ah you were answering my request for a chainwheel corks etc, I believe you suggested aralditing some pto discs on the chainwheel which I did and, as they say, never looked back, works a treat thank you, cost about £24 plus the tube of araldite, kind regards
sorry Paul I did,mt realise it was you posting, missed the change of deponent and thought it was still Mccorkings, I must try harder!Edited by - GOLDSTAR on 14 May 2012 7:06:35 PM
must continue to try harder because I mean Greasemonkey!! oh sigh!Edited by - GOLDSTAR on 14 May 2012 7:07:37 PM
sorry Paul I did,mt realise it was you posting, missed the change of deponent and thought it was still Mccorkings, I must try harder!Edited by - GOLDSTAR on 14 May 2012 7:06:35 PM
must continue to try harder because I mean Greasemonkey!! oh sigh!Edited by - GOLDSTAR on 14 May 2012 7:07:37 PM
- greasemonkey62
- Posts: 562
- Joined: Wed Jun 16, 2010 12:37 pm
- Location: SOUTH YORKSHIRE UK
AJS model 31 clutch
The clutch I am told is a 1950`s 500 Norton one, and luckily AMC clutch studs fit it perfectly along with the cup and springs and spring adjusting screws, I had not realised that parts were being shared at this time, I thought AMC and Norton didnt start sharing parts until after 1960, cheers all.
-
- Posts: 158
- Joined: Mon Jan 01, 1990 12:00 am
- Location: CAMBRIDGESHIRE UK
AJS model 31 clutch
The original Norton clutch also has a two piece clutch push rod that has a large mushroom head that lifts the pressure plate. This makes the pressure plate lift squarely and there is no need to adjust the springs individually. The AMC pressure plate has the push rod adjuster screw in the centre of the plate so the mushroom cannot be used.
- greasemonkey62
- Posts: 562
- Joined: Wed Jun 16, 2010 12:37 pm
- Location: SOUTH YORKSHIRE UK
AJS model 31 clutch
with regards my last comment it turns out the clutch centre tabs on my "norton?" clutch are 7mm wide, whereas the AJS replacement plates tabs are 10mm wide, so although it does fit not all parts are the same size, the spring studs fit fine its just the plates tabs that are different widths.
-
- Posts: 38
- Joined: Wed Aug 26, 2009 4:28 pm
- Location: WILTS UK