I would say most people who do up an old bike end up spending more on it than it is worth unless they do all the paintwork and mechanical work themselves and had purchased it at a good price. If they keep it some years and see the value rise they may cover the expenditure but If you do keep it and use it in the interim you will probably spend more time and money on keeping it running. Try owning 6 bikes!ColourNcoat wrote:....... It does stick in my gut that I have to spend yet more money on this little treasure to finally get it done.
I know you can't put a price on everything but in this case I have to draw a line somewhere, yet I have to get it finished.
How many people have spent more than something is worth without having sentimental attachments?
Regards
Carb question.
- clive
- Member
- Posts: 5669
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Carb question.
clive
if it ain't broke don't fix
if it ain't broke don't fix
- Duncan
- Member
- Posts: 2138
- Joined: Thu Jul 10, 2003 1:00 am
- Location: HAMPSHIRE UK
Re: Carb question.
A concentric may be a cheaper option or even a wassell AMAL copy if originality is not a major concern and a budget has to be worked to, perhaps any one who has made this modification on a G2/14 could confirm their settings for you?
-
- Posts: 2884
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Carb question.
Hi
You probably don't 'need' a new carb if you are prepared to accept slightly less than optimal tick-over. This carb, from one of my recent restorations is an original from 1958 and is now back in use:
A new carb will have no wear between the slide and bore so will improve slow running, it will also have clean galleries and new jets etc. so that's your best chance of making a serious step forward.
If you budget is tight and you can live with a slightly erratic tick over, (I do and I'm sure I'm not alone), I would thoroughly clean the carb, (which you say you have already done), and replace the pilot jet, (£6), then set the slow running as per one of the documents previously linked. If it turns out not to be the pilot jet it's cost you £6 and you now have a spare
Just a thought - how are you installing the pilot jet? it should be fully screwed into the carb body and then the cap fitted, (not screwed into the cap and then installed into the body).
Regards Mick
You probably don't 'need' a new carb if you are prepared to accept slightly less than optimal tick-over. This carb, from one of my recent restorations is an original from 1958 and is now back in use:
A new carb will have no wear between the slide and bore so will improve slow running, it will also have clean galleries and new jets etc. so that's your best chance of making a serious step forward.
If you budget is tight and you can live with a slightly erratic tick over, (I do and I'm sure I'm not alone), I would thoroughly clean the carb, (which you say you have already done), and replace the pilot jet, (£6), then set the slow running as per one of the documents previously linked. If it turns out not to be the pilot jet it's cost you £6 and you now have a spare
Just a thought - how are you installing the pilot jet? it should be fully screwed into the carb body and then the cap fitted, (not screwed into the cap and then installed into the body).
Regards Mick
You do not have the required permissions to view the files attached to this post.
-
- Posts: 140
- Joined: Thu Oct 22, 2020 8:07 pm
- Location: Monmouthshire UK
Re: Carb question.
Hi Duncan,Duncan wrote:A concentric may be a cheaper option or even a wassell AMAL copy if originality is not a major concern and a budget has to be worked to, perhaps any one who has made this modification on a G2/14 could confirm their settings for you?
Its not so much of a cheaper option, its more to do with a resolve for the outlay.
If its a fifty pound outlay or a two hundred pound outlay and its still not fixed
Thanks for the options
Regards
Roger
-
- Posts: 140
- Joined: Thu Oct 22, 2020 8:07 pm
- Location: Monmouthshire UK
Re: Carb question.
Hi Mick,Mick D wrote:Hi
You probably don't 'need' a new carb if you are prepared to accept slightly less than optimal tick-over. This carb, from one of my recent restorations is an original from 1958 and is now back in use:
A new carb will have no wear between the slide and bore so will improve slow running, it will also have clean galleries and new jets etc. so that's your best chance of making a serious step forward.
If you budget is tight and you can live with a slightly erratic tick over, (I do and I'm sure I'm not alone), I would thoroughly clean the carb, (which you say you have already done), and replace the pilot jet, (£6), then set the slow running as per one of the documents previously linked. If it turns out not to be the pilot jet it's cost you £6 and you now have a spare
Just a thought - how are you installing the pilot jet? it should be fully screwed into the carb body and then the cap fitted, (not screwed into the cap and then installed into the body).
Regards Mick
My carb wasn't that bad
I see exactly what you are saying and if that can be brought back to life, there is still hope
The port on my bike is 1 1/8 and the 376 is 1 1/16 so would this make a big difference?
Sorry to all for going back and forth
Regards
Roger
-
- Posts: 2884
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Carb question.
Sorry - forgot about the throat mismatch.
There will be a pressure drop as the air fuel mixture transits over the step, this can cause the fuel vapour to partially condense and may result in poor running. You could blend the different diameters together over the length of the insulator which would minimise the effect but ideally the carb needs to be matched to the head.
Give blending a try if your insulator will allow it, it's free, and replace the pilot jet.
Regards Mick
There will be a pressure drop as the air fuel mixture transits over the step, this can cause the fuel vapour to partially condense and may result in poor running. You could blend the different diameters together over the length of the insulator which would minimise the effect but ideally the carb needs to be matched to the head.
Give blending a try if your insulator will allow it, it's free, and replace the pilot jet.
Regards Mick
-
- Posts: 140
- Joined: Thu Oct 22, 2020 8:07 pm
- Location: Monmouthshire UK
Re: Carb question.
This was previously mentioned by Clanger who kindly put up a link on the subject. I did do a port match and made brass bushes to stop gasket/insulator misalignment. Unfortunately this didn't make any difference or improvements.Mick D wrote:Sorry - forgot about the throat mismatch.
There will be a pressure drop as the air fuel mixture transits over the step, this can cause the fuel vapour to partially condense and may result in poor running. You could blend the different diameters together over the length of the insulator which would minimise the effect but ideally the carb needs to be matched to the head.
Give blending a try if your insulator will allow it, it's free, and replace the pilot jet.
Regards Mick
Just when I think there could be a possibility of a fix its a case of biting the bullet and get a new 389/82.
Regards
Roger
-
- Posts: 140
- Joined: Thu Oct 22, 2020 8:07 pm
- Location: Monmouthshire UK
Re: Carb question.
Big thank you to everyone for the advice given and have just ordered a new 389/82 from club spares so thanks and fingers crossed
Regards
Regards
Roger
- Samuel
- Member
- Posts: 1068
- Joined: Tue Sep 09, 2003 1:00 am
- Location: Somerset UK
Re: Carb question.
As I suggested on 11th February. Pleased you arrived at that conclusion.ColourNcoat wrote:Big thank you to everyone for the advice given and have just ordered a new 389/82 from club spares so thanks and fingers crossed
Regards
Sam
-
- Posts: 140
- Joined: Thu Oct 22, 2020 8:07 pm
- Location: Monmouthshire UK
Re: Carb question.
And thank you for that SamSamuel wrote:As I suggested on 11th February. Pleased you arrived at that conclusion.ColourNcoat wrote:Big thank you to everyone for the advice given and have just ordered a new 389/82 from club spares so thanks and fingers crossed
Regards
It's because it still wouldn't have been right because the carb was a mismatch for my cylinder head. Besides I was probably getting on everyone's nerves
Time will tell
Roger