Can anyone convert feet-Lbs to Lbs-feet for torque wrench settings??
Torque wrench setting conversion?
-
- Posts: 24
- Joined: Mon Apr 28, 2008 12:44 pm
- Location: ESSEX UK
- Youngster
- Posts: 213
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: GLOS UK
Torque wrench setting conversion?
Hi Paul, arent they the same thing?
Cheers
Ian
Cheers
Ian
Too many bikes, So little time!!
-
- Posts: 24
- Joined: Mon Apr 28, 2008 12:44 pm
- Location: ESSEX UK
Torque wrench setting conversion?
HiIan,
Im not sure, Maths wasnt my best subject at School, in fact I thought my name was Coulddobetter for many years!
Thanks for your interest though.
Regards
Paul
Im not sure, Maths wasnt my best subject at School, in fact I thought my name was Coulddobetter for many years!
Thanks for your interest though.
Regards
Paul
- Eamonn
- Webmaster
- Posts: 2235
- Joined: Sun Jan 01, 1995 12:00 am
- Location: OXFORDSHIRE UK
- Contact:
Torque wrench setting conversion?
quote:
Can anyone convert feet-Lbs to Lbs-feet for torque wrench settings??
A foot-pound is the amount of effort that a 1 pound weight applies at a distance of 1 foot from the (in this case) nut/bolt. A pound-foot is exactly the same force over exactly the same distance - thus you can consider them the same thing.
According to Wikipedia a pound-foot is often used by machine manufacturers as the measurement of output from an engine whereas a foot-pound is the amount of energy of input that you need to put in.
Finally 1 foot-pound is 1 1/3 Newton-Metres (Nm), so to convert between foot-pounds and Nm multiply by 4 and divide by 3. To convert from Nm to foot-pounds multiply by 3 and divide by 4.
Can anyone convert feet-Lbs to Lbs-feet for torque wrench settings??
A foot-pound is the amount of effort that a 1 pound weight applies at a distance of 1 foot from the (in this case) nut/bolt. A pound-foot is exactly the same force over exactly the same distance - thus you can consider them the same thing.
According to Wikipedia a pound-foot is often used by machine manufacturers as the measurement of output from an engine whereas a foot-pound is the amount of energy of input that you need to put in.
Finally 1 foot-pound is 1 1/3 Newton-Metres (Nm), so to convert between foot-pounds and Nm multiply by 4 and divide by 3. To convert from Nm to foot-pounds multiply by 3 and divide by 4.
Corners like a Lego man
-
- Member
- Posts: 1221
- Joined: Fri Jan 01, 1993 12:00 am
- Location: WEST MIDLANDS UK
Torque wrench setting conversion?
ft/lbs & lbs/feet are one and the same thing just a different way of expressing it.
As for your lightweight cylinder head the book says 35 ft/lbs that's the same as the heavyweight singles, but quite a lot more than the twins that have only 16 ft/lbs for the 5/16" dia studs and 25 ft/lbs for 3/8" ones.
If you only have Newton Metres on your torque wrench you will need to convert at the rate of 1.36 Nm for every ft/lb so 35 ft/lbs would be 47 Nm.Edited by - Eric on 24 Aug 2008 4:12:51 PM
As for your lightweight cylinder head the book says 35 ft/lbs that's the same as the heavyweight singles, but quite a lot more than the twins that have only 16 ft/lbs for the 5/16" dia studs and 25 ft/lbs for 3/8" ones.
If you only have Newton Metres on your torque wrench you will need to convert at the rate of 1.36 Nm for every ft/lb so 35 ft/lbs would be 47 Nm.Edited by - Eric on 24 Aug 2008 4:12:51 PM
-
- Posts: 24
- Joined: Mon Apr 28, 2008 12:44 pm
- Location: ESSEX UK
Torque wrench setting conversion?
Hi everyone,
Thank you so much for all your answers, I knew you would come up trumps
Thanks once again
Paul M
Thank you so much for all your answers, I knew you would come up trumps
Thanks once again
Paul M