Anyone got a pinion puller spare (or an opinion)!
-
- Posts: 393
- Joined: Wed Sep 30, 2009 6:54 pm
- Location: BUCKS UK
Anyone got a pinion puller spare (or an opinion)!
I'm trying to separate my timing pinion ('52 18s) from it's shaft. Does anyone have a pinion puller they want to be parted from (for a fee) or (here we go) have an opinion on them??
I've tried adapting a 3 leg puller but that pulled itself apart as I had to grind down the feet to fit behind the pinion. Also tried applying heat but it's still defeating me.
I read a thread about dropping the bush out through the cases but the teeth look like they are proud (could be an illusion) and anyway presumably you still have to get the pinion off.
So, who's got an opinion (or puller) to share.
Tom
I've tried adapting a 3 leg puller but that pulled itself apart as I had to grind down the feet to fit behind the pinion. Also tried applying heat but it's still defeating me.
I read a thread about dropping the bush out through the cases but the teeth look like they are proud (could be an illusion) and anyway presumably you still have to get the pinion off.
So, who's got an opinion (or puller) to share.
Tom
-
- Posts: 7721
- Joined: Tue Nov 22, 2005 6:01 pm
- Location: UK
Anyone got a pinion puller spare (or an opinion)!
use the correct tool from JLS
nothing else will do.
unless you feel like a 75 mile run to here and I'll do it.
http://www.ajs-matchless.com/pic_displa ... 1804Edited by - itma on 28 Feb 2012 10:09:05 PMEdited by - itma on 28 Feb 2012 10:11:40 PM
nothing else will do.
unless you feel like a 75 mile run to here and I'll do it.
http://www.ajs-matchless.com/pic_displa ... 1804Edited by - itma on 28 Feb 2012 10:09:05 PMEdited by - itma on 28 Feb 2012 10:11:40 PM
-
- Posts: 393
- Joined: Wed Sep 30, 2009 6:54 pm
- Location: BUCKS UK
Anyone got a pinion puller spare (or an opinion)!
(B-2151)
EXTRACTOR; TIMING GEAR £20.77
Is this the part you mean?
I've heard that these may not be up to the job bearing in mind the engine I have has been sat for some time. Don't want to spend £25 and still end up no closer to the goal.
EXTRACTOR; TIMING GEAR £20.77
Is this the part you mean?
I've heard that these may not be up to the job bearing in mind the engine I have has been sat for some time. Don't want to spend £25 and still end up no closer to the goal.
-
- Posts: 7721
- Joined: Tue Nov 22, 2005 6:01 pm
- Location: UK
Anyone got a pinion puller spare (or an opinion)!
That's the one.
cant speak for the ones JLS sell but I have had my one for decades.
The pinion should not be hard to remove no matter how long its been on.
They have to be seated properly, sometimes a side ways tap is need to tuck its rim behind the pinion.
Outside of personal experience I take all such stories of dud kit with a pinch of salt,mostly its down to cackhandedness and poor tool use.
Which is why I never lend tools but will do it for you.
besides if you bought a used one it would be from JLS anyway?
cant speak for the ones JLS sell but I have had my one for decades.
The pinion should not be hard to remove no matter how long its been on.
They have to be seated properly, sometimes a side ways tap is need to tuck its rim behind the pinion.
Outside of personal experience I take all such stories of dud kit with a pinch of salt,mostly its down to cackhandedness and poor tool use.
Which is why I never lend tools but will do it for you.
besides if you bought a used one it would be from JLS anyway?
-
- Posts: 393
- Joined: Wed Sep 30, 2009 6:54 pm
- Location: BUCKS UK
Anyone got a pinion puller spare (or an opinion)!
It's sounding more like a good investment after all. Thanks for the offer but I don't want to be the cackhanded one who ruins a prized tool.
Thanks, I will order one tonight.
Thanks, I will order one tonight.
-
- Posts: 7721
- Joined: Tue Nov 22, 2005 6:01 pm
- Location: UK
Anyone got a pinion puller spare (or an opinion)!
Mine is a prized tool in that not only is it the gen kit but was a gift from an ex Plumstead man who one day left a note on my AJS asking if I would like his bin load of new AMC spares, bits and bobs
Those were the days.
Those were the days.
-
- Posts: 393
- Joined: Wed Sep 30, 2009 6:54 pm
- Location: BUCKS UK
Anyone got a pinion puller spare (or an opinion)!
A previously well lubricated, heated and attacked with various ill-fitting make-shift tools, pinion popped off tonight with the correct tool.
Thanks again for the offer ITMA, most appreciated. I'm now equipped to tackle more of those tricky little blighters!
Thanks again for the offer ITMA, most appreciated. I'm now equipped to tackle more of those tricky little blighters!
-
- Member
- Posts: 790
- Joined: Sat Jan 01, 1994 12:00 am
- Location: LINCOLNSHIRE UK
Anyone got a pinion puller spare (or an opinion)!
well done Tom, now all you need to do is hire the puller out five times at £5 a time to recoup your investment.Borower to pay postage each way of course
-
- Posts: 393
- Joined: Wed Sep 30, 2009 6:54 pm
- Location: BUCKS UK
-
- Member
- Posts: 36
- Joined: Tue Mar 14, 2023 10:26 am
- Location: UK
Re: Anyone got a pinion puller spare (or an opinion)!
Anyone any idea who JLS are (not the boy band) as I need one of these and the club spares are out of stock. Or is there another tool or method that would remove the timing pinion from a HW single?